- HOW TO MACHINE AN STL FILE IN MASTERCAM X5 MANUAL
- HOW TO MACHINE AN STL FILE IN MASTERCAM X5 SOFTWARE
- HOW TO MACHINE AN STL FILE IN MASTERCAM X5 WINDOWS
!Switch to the Advanced interface and create a Morph between 2 surfaces toolpath to add depth cuts and avoid gouging the blades. Objectives: The Student will create 5-Axis milling toolpaths consisting of: !Create a Impeller floor surface without tiltcurve toolpath from the Custom Application toolpath family to rough the area between two blades. TUTORIAL #4 ROUGH & FINISH IMPELLER WITHOUT TILTCURVE 4-1 Tutorial #5 Collision Control Strategies. 3-1 Tutorial #4 Rough & Finish Impeller Without Tiltcurve. 2-1 Tutorial #3 Finish Surfaces Toolpath. A-1 Tutorials Tutorial #1 Projection Toolpath.
HOW TO MACHINE AN STL FILE IN MASTERCAM X5 WINDOWS
Windows, Windows XP, Windows Vista and Windows NT are registered trademarks of Microsoft Corporation.Īdvanced Multiaxis Training Tutorial Contents Getting Started.
Microsoft, the Microsoft logo, MS, and MS-DOS are registered trademarks of Microsoft Corporation N-See is a registered trademark of Microcompatibles, Inc. Trademarks Mastercam is a registered trademark of CNC Software, Inc. This document may not, in whole or part, be copied, photographed, reproduced, translated or reduced to any electronic medium or machine readable form without prior consent, in writing, from In-House Solutions Inc.
HOW TO MACHINE AN STL FILE IN MASTERCAM X5 MANUAL
Copyrights This manual is protected under International copyright laws. Some jurisdictions do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. has been advised of the possibility of such damages. be liable for direct, indirect, or consequential damages resulting from any defect in the manual, even if In-House Solutions Inc. Should the manual prove defective following its purchase, the buyer (and not In-House Solutions Inc., its distributer, or its retailer) assumes the entire cost of all necessary servicing, repair, of correction and any incidental or consequential damages. manual is sold or licensed "as is." The entire risk as to its quality and performance is with the buyer.
HOW TO MACHINE AN STL FILE IN MASTERCAM X5 SOFTWARE
makes no warranties, either express or implied, with respect to this manual or with respect to the software described in this manual, its quality, performance, merchantability, or fitness for any particular purpose. Disclaimer Of All Warranties And Liability In-House Solutions Inc. reserves the right to make improvements to this manual at any time and without notice. All rights reserved Software: Mastercam X5 Author: Mariana Lendel ISBN: 978-1-92 Revision Date: November 3, 2010 Mastercam X5 Training Tutorials - Advanced Multiaxis Copyright: 1998 -2010 In-House Solutions Inc. Hope some of that makes sense to you.To order more books: Call 1-80 or Visit or Contact your Mastercam dealer You can also create multiple boundaries and use that and z depth limits to control what you want to cut. You still need to select say all the outside, change that to a color, then select the inside (or the floors, walls, radii, whatever you want to seperate from the rest) and change that to a different color so they are grouped for the next set of operations or whatnot. You can make this easier to repeat if you change colors however as I mentioned. I think with surfaces (similar to using solid faces) you are basically stuck selecting them individually if you don't want to select the inside of your part and outside both. Depending on your orientation, go to the front view and then window select and you can control the the z depth (in the top view) a little easier, but this will still select all (inside and outside of the shape). You could change the color of what you want to cut and select that color, but then you still need to select them to change the color. As to selecting the surfaces, not sure as I have almost exclusively used solid bodies for the past few years.
Probably the easiest path to create, maybe not the most efficient, but you could have that programmed in 5 minutes and get it in the machine and running while you work on the rest of programming.
0 kommentar(er)
